Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands

Other

$109.50
Eliminate dropped chains forever with the new OneUp Components Bash Guide. As the trend for lower and slacker bikes continues, chainring protection is becoming even more important. Revised for 2019 the OneUp Bash Guide uses simple, one tool installation and adjustment as well as an all new tool less flip The OneUp Bash Guide was developed with input from top EWS World racers and can be seen all over this years circuit. Reinforced Nylon bash guards and a back plate cut from 8mm thick 7075-T6 aluminum, ensure that the OneUp Bash Guide can handle the biggest hits, but at a weight of only 105g (34T) you may forget it’s even there. NOT JUST FOR ENDURO RACERS. The OneUp Bash Guide is equally at home on your trail bike, where the extra bash protection is a must for aggressive riders or on your DH rig. With the popularity of clutch derailleurs, it is no longer necessary to run a chain guide with a lower roller to effectively tension your chain. DH racers and Bike Park rippers will appreciate the huge reduction in drag with the elimination of the lower roller, without sacrificing any strength or chain retention. The OneUp Bash Guide includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. FEATURES - Tool less upper guide flip - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Black Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) - Patented US 10,053,188 Other Patents Pending SPECS - Weight: 90g 28-30T, 105g 32-34T, 110g 36T - Capacity: 28-36T - Chainline: 7.5mm adjustment - Mount: ISCG05 - Color: Black top guide piece included - Material: 7075 aluminum, top guide glass reinforced thermoplastic
$59.00
If you're not looking for chain retention or your bike has an integrated chain guide, you can still add some bash protection with the OneUp ISCG05 Underbash. The Underbash includes 3 different sizes of bash plate for compatibility with chainrings from 28-36T. Designed for frames with 2 ISCG05 tabs only (Evil, Rocky Mountain, etc). If your bike has three ISCG05 tabs, check with the frame manufacturer to ensure the lower tabs are strong enough for a bash application. Failure to do so could result in frame damage. FEATURES - Install without removing your crank - Single tool install and adjustment - Boost compatible - Oval Compatible - Stainless Steel hardware - Includes 3 bash plates (28-30T, 32-34T, 36T) SPECS - Weight: 68g 32-34T - Capacity: 28-36T - Chainline: 2.5mm adjustment - Mount: ISCG05 2-Bolt ONLY - Color: Black - Material: 7075 aluminum, glass reinforced thermoplastic
$33.00
The EDC Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8" aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. KIT INCLUDES - EDC TOP CAP - EDC steerer plug - 2x 1mm, 3mm, & 5mm Headset Spacers
$26.00
V2 dropper remote clamp for 22.2mm handlebar.
$25.00
This kit includes all the parts required to rebuild your V1 Dropper Post. - Replacement Seal - Upper and lower bushings - Anti-rotation pins - Compatible with V1 Dropper Post ONLY. We have found that ~95% of posts with slow top out were caused by low air pressure. Please make sure to check this first and do so with the post fully extended. Proper air pressure is 280-300psi at full extension, and the valve is located under the top clamp. If you are still having slow top out then there is a possibility that the upper white bushing needs replacement. This will be evident by the original bushing being difficult to reinstall after being removed.
Page 1 of 1